Short answer: The Cooling Company installs commercial HVAC across North Las Vegas, from rooftop packaged units on distribution warehouses in the Apex Industrial Park to VRF and VAV systems for offices along the Craig Road and Cheyenne corridors. We start with a Manual N or block load calculation, pull Clark County permits, and engineer for the desert: dusty intakes, high IEER for big footprints, and economizers that actually earn their keep. Licensed in Nevada since 2011 (C-21 #0075849 and C-1D #0078611), with a $700,000 bid limit. Call (702) 567-0707.
HVAC built for how North Las Vegas actually works
North Las Vegas is one of the fastest-growing industrial markets in the Southwest, and the buildings going up here have HVAC demands a residential mindset cannot touch. A 600,000 square foot fulfillment center near Apex needs a completely different ventilation strategy than a dental office on Craig Road, which needs something different again from a powder-coating line off Cheyenne. We install all three, and we engineer each one to the building, not to a catalog default.
That distinction matters because in the Mojave, the wrong system does not just run inefficiently, it fails early. Dust loads the coils, summer design temperatures push undersized equipment past its limits, and a warehouse ventilated for a different occupancy turns into an unworkable oven by July. We size, specify, and install so that does not happen.
Apex Industrial Park and the big-box warehouses
The Apex Industrial Park and the surrounding logistics belt are defined by enormous high-bay buildings: distribution centers, e-commerce fulfillment, cold-adjacent storage, and cross-dock facilities. Conditioning a footprint this large with traditional cooling alone is rarely the right call. For many of these warehouses the smarter approach combines large rooftop packaged units for the conditioned office and pick zones with evaporative cooling and engineered make-up air for the open warehouse floor.
Evaporative (swamp) cooling works in our climate precisely because Apex air is dry. It moves large volumes of cooler air at a fraction of the energy cost of mechanical refrigeration, exactly what a high-bay space with roll-up doors and constant air exchange needs. Where process or product demands tighter control, we specify high-IEER rooftop units sized to the actual envelope and internal heat gain, not a rule-of-thumb tonnage. Make-up air units replace the air exhausted by dock fans so the building stays at the right pressure and the doors are not fighting a vacuum every time a trailer backs in.
Light manufacturing and process loads
North Las Vegas has a deep base of light manufacturing, fabrication, and assembly. These buildings throw a wrench into standard HVAC math because the people are not the main heat source. Ovens, presses, welding, compressors, and motors generate process heat that a comfort-cooling load calc will completely miss. We account for that by treating process heat as its own line item: spot cooling and dedicated exhaust where the heat is generated, general ventilation sized to the real air changes per hour the work requires, and tempered make-up air so the shop is not pulling unconditioned summer air through every crack to feed the exhaust hoods.
Offices, retail, and the Craig Road and Cheyenne corridors
The commercial corridors along Craig Road, Cheyenne Avenue, and the retail centers serving the surrounding neighborhoods need comfort, quiet, and zoning. For multi-tenant office buildings and suites with varied occupancy, VAV (variable air volume) and VRF (variable refrigerant flow) systems are usually the answer. VRF gives each tenant or zone independent control, recovers heat between zones that are cooling and heating at the same time, and runs quietly, which matters in a medical or professional space. For retail, we balance the storefront load against the back-of-house and design for the door-open reality of a busy shopping center.
How a commercial install actually runs
1. Load calculation and engineering
Every project starts with a real load calculation. For smaller commercial spaces that means a Manual N calculation; for large industrial footprints it means a block-and-zone load model that accounts for envelope, glazing, occupancy, process heat, ventilation code minimums, and our brutal summer design temperature. Oversizing wastes capital and causes short-cycling and humidity swings. Undersizing means a building that never recovers on a 110 degree afternoon. We size to the building.
2. Equipment selection
We are not married to one manufacturer. Depending on the building we specify:
- Rooftop packaged units (RTUs): the workhorse for retail, offices, and conditioned warehouse zones. We prioritize high-IEER models for large footprints because part-load efficiency is where the savings live in our long cooling season.
- Split and ducted systems: for smaller suites and tenant build-outs where a rooftop curb is not practical.
- VRF and VAV: for zoned offices, medical, and multi-tenant buildings that need independent control and quiet operation.
- Large-tonnage and chiller plants: for campuses and high-density buildings where central plant economics beat a roof full of packaged units.
- Evaporative cooling and make-up air: for high-bay warehouse floors, dock areas, and any space with high air-exchange or exhaust demands.
3. Clark County permitting and code
Commercial HVAC in North Las Vegas runs through Clark County and City of North Las Vegas building and mechanical permitting, with work performed to the adopted International Mechanical Code and current Nevada energy code. We handle the permit applications, the mechanical plans, the equipment cut sheets, and the inspections. Title 24-style energy provisions, ventilation rate compliance, economizer requirements, and rooftop structural and electrical coordination are part of the package, not an afterthought. You should never be the one chasing an inspector.
4. Desert and dust engineering
This is where local experience separates a system that lasts from one that struggles. North Las Vegas air carries fine desert dust, and near the industrial parks and unpaved-adjacent parcels it carries more. Warehouse intakes and economizer hoods load up fast, so we spec filtration MERV-rated to the application, accessible filter racks, and intake placement that is not sitting in the dirtiest air on the lot. Condenser coils get the same consideration, because a dust-blinded coil in August is a capacity loss exactly when you need every ton. We design for cleanability, because a system that is hard to service gets neglected.
5. Energy efficiency and controls
Energy is one of the largest operating costs in a commercial building, and our climate makes the HVAC the biggest single piece of it. We build efficiency into the install:
- Economizers that pull in free cooling on the cooler mornings and shoulder seasons we do get, properly commissioned so they actually work instead of failing closed.
- Demand-control ventilation for warehouses and variable-occupancy spaces, so you are not conditioning and ventilating an empty building at full rate.
- Building automation systems (BAS) that schedule, set back, trend, and alarm, giving facility managers visibility and the ability to tune the building over time.
- High part-load efficiency equipment selected for our long cooling season, where the unit spends most of its life at part load, not peak.
NV Energy offers commercial efficiency incentives for qualifying high-efficiency equipment and controls; we will tell you honestly what your project may qualify for and help with the documentation. We do not promise rebates we cannot verify, and we do not cite expired federal tax credits to close a sale.
6. Phased installs that keep you running
An operating warehouse, a busy clinic, or a multi-tenant retail center cannot simply shut down for a week while the HVAC gets replaced. We plan phased and after-hours installations: section by section, zone by zone, or off-shift, with temporary cooling staged where it is needed so product, people, and operations keep moving. The point of the install is to improve the building, not to halt the business that pays for it.
7. Maintenance handoff
Energizing the new system is not the day our involvement ends. We hand off with as-built documentation, equipment registration for warranty, filter and service schedules, and a maintenance plan built around our climate. Commercial equipment in the Mojave needs more frequent coil cleaning and filter service than the manufacturer's temperate-climate default, and a planned maintenance agreement is how you protect the capital you just invested. We can carry that maintenance ourselves so the same team that knows your building keeps it running.
Why North Las Vegas businesses choose The Cooling Company
We have served Southern Nevada since 2011 and hold the licenses commercial work requires: Nevada C-21 (#0075849) and C-1D (#0078611), with a $700,000 bid limit. We carry a 4.8 star rating across 835 plus reviews, and we bring the same precision to a multi-unit rooftop array that we bring to a single-zone tenant build-out. Local crews, local permitting knowledge, and equipment specified for the desert rather than a textbook climate.
Frequently asked questions
How long does a commercial HVAC installation in North Las Vegas take?
It depends entirely on scope. A single rooftop unit replacement on a small retail suite can be done in a day or two. A full multi-unit warehouse or a phased office building can run several weeks. The honest answer comes after the load calculation and a site walk, when we can stage the work around your operations and the permit and inspection timeline. We give you a real schedule, not a guess.
Do you handle the Clark County permits and inspections?
Yes. We manage the permit applications, mechanical plans, equipment cut sheets, and inspections through Clark County and the City of North Las Vegas. You should not be the one explaining your HVAC to an inspector. Pulling permits also protects you: permitted, inspected work is what holds up for insurance, financing, and resale.
Should a warehouse near Apex use refrigerated cooling or evaporative cooling?
Often a combination. The dry desert air around Apex makes evaporative cooling very effective and far cheaper to run for large, high-air-exchange warehouse floors, while refrigerated rooftop units handle the conditioned office and any product zones that need tight control. The right split depends on what you store, how the building is used, and your door and exhaust activity. We model it before we recommend it.
Can you install without shutting down our operations?
In most cases, yes. We plan phased and after-hours installs, working zone by zone or off-shift and staging temporary cooling where needed so production, patients, or customers are not interrupted. Keeping your business running is part of the install plan, not an afterthought.
How do you size a system for a building with process heat from machinery?
We treat process heat as its own load. A standard comfort-cooling calculation ignores the heat thrown off by ovens, presses, motors, and compressors, which is why manufacturing spaces so often end up undercooled. We add the process load, design dedicated exhaust and spot cooling where the heat is generated, and size make-up air so the building is not starving the exhaust hoods. That is how you get a shop that is actually workable in August.
Replacing an aging commercial system rather than installing new? See our commercial HVAC replacement in North Las Vegas page for system assessment, old-equipment removal, and minimal-downtime swap details.
Get a commercial HVAC quote for North Las Vegas
If you are building, expanding, or replacing HVAC for a warehouse, plant, office, or retail space anywhere in North Las Vegas, from Apex to the Craig Road and Cheyenne corridors, talk to a team that engineers for this market. We will walk the site, run the numbers, and give you a system that fits the building and the desert. Call The Cooling Company at (702) 567-0707.
Share This Page
